Fourth try on a print. Tried to add some adhesive to the bed to get it to stick better. Watched the first two layers and went to bed. Woke up to a printer on strike.
You must log in or register to comment.
OH NO
I don’t see a beginning of a print anywhere, did it not even manage to do the first layer?
If that’s the case, a word of advice to always be present for the first 2 layers of your prints, at least for the longer ones.
I didn’t take the photo immediately - tried cleaning a bit before it occurred to me to document it.
Nozzle not seated properly?
I just had this happen too and it was caused by a bad z-offset reading. The nozzle hooked one of the parts on the bed that came loose and drug it around while forming the blob.
How did you diagnose that?
or no nozzle?
I’ve had 3 blobs over the years, all caused by an otherwise benign issue turned into that because filament got caught in a silicon sock.
I mean putting a lot of sticky stuff in a sock will usually do that.
I don’t think it’s supposed to do that
I’ve been doing 3D printing regularly for a decade or so now… Never had a blob.
I’ve been printing for two weeks, and I had one.
deleted by creator
Atleast it didnt get wedged in the heat sink… Thats what happeneed to my last blob, had to replace the entire hot end.
that looks like delicious taffy. like an abba zaba
I had that happen once. it just bout pushed the fan off the head since the clips are broken but it fits good enough™️
If you use OctoPrint you can get plugins that use a camera to watch for failed prints like stinging etc and it will stop the print if it fails.
I forget the name of the plugins right now. I went to say “Dr” something.
It used to be Spaghetti Detective, but they wanted to be trendy so it’s “Obico” I think now lol
Thanks for adding the extra detail.
I have since noticed OP has only been printing two weeks so perhaps they don’t want to go down this route just yet, but it is another fun project and they will need to print some things to hold the web cam etc so could be something to focus on.
Yeah, it’s not bad! If it’s got a good clean view it can tell you when things start to look a little sus before disaster strikes haha.
It’s even self-hostable, and a modest dedicated graphics card can be used to run the LLM completely locally. I haven’t been able to get that running on my server yet though. (Nvidia drivers. Agh)
Otherwise they’re pretty “freemium”, which is understandable.
I’ve been out of the game lately though. :)
Thanks for this.
I have been out of the game for a bit too. Saving for a Bambu Labs printer as I spend more time levelling my Ender than printing 😂
O was also thinking about that, but since Bambu is so closed, I’ve started looking into other options and Qidi looks nice too
Never heard of Qidi, thanks for sharing that! Bambu concerns me, frankly, from the “too good to be true in capitalism-land” standpoint.
They’re obviously pretty quality built and do a great job off the shelf, but the closed source software is iffy to me too. I think some are suspicious they just don’t want to reveal they’re basically running tweaked Klipper lol. I’m lured by that temptation of not having to tweak and fiddle for weekends prospect too, but if I can’t touch it at all or know how it works, my Ender3v2 still seems more appealing!
I’m concerned if other companies don’t seriously step up their game, Bambu will reach market saturation and then go for the" enshittification rug pulling to impress investors" special.
Anyway don’t want to be too negative, clearly people are enjoying those machines. But the maker community definitely needs to be ready to raise a riot if Bambu starts taking notes from HP / Apple / John Deere. :)
They’re a bit too reliant on the cloud and the event where „their” printers (that the users both and were using at their homes) re-printed last job because of some server issue was a bit concerning. And definitely the fact that if your printer does have issues you can’t fix/calibrate much without them is alarming to me. I’m using a K1 which might need some work but it’s manageable. If I were looking to upgrade I’d probably get Qidi Q1 Pro - same price ballpark as K1 or P1S, while the features it has seem to be closer to X-series
This was what most annoyed me on my Ender 3. Now with a bambu A1 its fire-and-forget. And no failed prints yet, with daily use.
That’s great to hear! I see a lot of positivity for the Bambu printers.
Yes. These are great machines. Please know, though, that p.e. the camera does inexplicably not work in LAN only mode (i.e. when not connected to the bambu cloud service), and that the AMS lite cannot fit every filament spool in the world due to its construction. First can be remedied with a separate webcam in your LAN, second with printed adaptors, alternative spools or just some squishy material (if the spool’s too big). I found that spools from dasfilament and recent ones from sunlu fit ok.
Yup, that’s how I’m using it;)
I’ve run into adhesion problems when the room gets colder.
works 99% of the time, but when ambient temp goes below 70°F everything starts failing.
Interesting. All of my prints that failed were running overnight when the temperature dropped.
What temps are you running your bed at?
Either 65°C or 70°C
PLA?
Yes
Yeah, in some parts of the world, a box surrounding the printer isn’t really a luxury.
Haven’t had problems since I upgraded.
Controlling temperature is important on FDM.
Hey, ummm… I think I see the problem. Your printer has diarrhea
I’ve a massive blob like this one time when the nozzle got clogged and the extruder created enough pressure to push the filament through the threads of the hotend block. It was on an Anet A8 and I ripped a lead off the thermistor trying to get the plastic off so I ended up replacing the entire hotend.
You can try to heat up the hotend to a fair bit under the melting point of the filament to where it’s soft and somewhat pliable but not runny or sticky and then trying to peel it off. Though you’d risk damaging any leads to the thermistor, heater, or your hands if you’re not careful.
Good luck on fixing the printer and getting back to printing again. 3D printing is a really time consuming hobby
Thanks. I am really frustrated with myself for letting this happen. Pulled everything apart and recovered most of everything, but managed to damage the clip that holds the extruder in place, so now I get to learn how to do surgery and replace the entire assembly. I wish I had gotten a bit more time before having to do a major repair…
It’s a learning experience. Is your nozzle torqued to spec? Only time I’ve seen something like this is when the heatbreak/nozzle weren’t set correctly on a v6 hotend, and even then it just oozed down, didn’t consume the entire heatsink. I kept that in my box of learning lol, swapped everything to hotends that are secured so they don’t spin freely after that, was petg so it degraded in the heat and was such a pain in the ass to remove from set screws, was ok writing it off.
Bed adhesion is often caused by surface cleanliness in my experience, some setting will influence it but you’re going to chase problems if your surface has residual oils, some surfaces are more sensitive to it but even the oils in your fingerprints can cause a loss of adhesion. Light dish soap and water is the general recommendation for a degreaser but be aware that this will damage some surfaces, I’ve got some that explicitly want only 99% IPA and another that only wants a clean microfibre cloth.
Drafts can cause an issue too, seen some abs fail becauae I didn’t have the enclosure latched properly and the doors worked their way open with vibrations from printing, I keep mine in my garage and live in Canada, enclosures are a must for me.
Aren’t these closed hardware? good luck finding replacements parts
They have all the parts available on their site.
Until they decide not to sell these anymore
There are already several aftermarket suppliers making parts for them, including a drop-in e3d hot end. Look, I generally prefer open source designs, but the hassle-free workflow with an X1C has been worth it.
Also, they sold a PILE of these things, I suspect aftermarket support will continue even if Bambu stops.
Remember about this comment in 10 years
Ten years… Someone apparently thinks they’re funny. I’d like to see their ten year old 3d printer that is still essentially using stock or equivalent components and hasn’t been essentially re-engineered from the ground up. Are you enjoying manually leveling that bed with thumbscrews and a scrap of paper? Still printing on tape, or maybe a piece of glass? This whole hobby is still moving relatively quickly and I wouldn’t be surprised to wind up working with additional axes or other unpredictable innovations ten years from now. Certainly we’ll have gone through multiple “ultimate” build surfaces by then.
Just because something it’s 10 years old doesn’t mean it’s useless or broken, especially when it’s open hardware and you can upgrade it or repair it. Your mentality seem to be shaped around closed hardware that you throw away once it’s broken or a new model is released.
Nope, you’re missing the point entirely. There’s absolutely nothing stopping me from walking into the other room, tearing apart my X1C and rebuilding it with, let’s say a klipper board, except that it works quite well at the moment… No printer bought right now is likely to be any different in that respect. You’re trying to act like it’s an i-phone, but it just isn’t.
So pretty much like every other company in existence? I don’t think there is any danger of BambuLabs disappearing anytime soon and their parts are dirt cheap.
So pretty much like every other company in existence?
Open hardware projects have the parts blueprints published
But you’re still relying on companies to produce these parts for you and they’ll only do it so long as the market is big enough to make it worth it for them.
Open source is definitely preferable, but at this point and time, their proprietary parts aren’t an issue at all as they’re cheap and readily available and with the popularity of these printers, I don’t see it being an issue for quite a long time. By then, I may have moved onto a new printer anyway since the market is constantly progressing.
Time will teach you the lesson
The lesson that all consumer electronics have a limited shelf life? That’s pretty well known.
looks at all the replacement parts that came with both my Bambu printers and the extra nozzles I ordered at the same time
What are you even talking about?
Did they include a new hotend or can you get one? I look on their site and see nothing for that.
Edit: I looked under Spare Parts and they weren’t there, but I see them under Accessories. And for $13, I’d sure as hell buy one when I got the printer. Along with a bunch of other parts, they’re quite reasonably priced.
You get a spare hotend with the purchase of a P1S so I assume they give you one with any of their printers.
You do on the P1S? I’m highly tempted to get one with the AMS, I have several printers that I’ve bought or built over the last 15 years, but even the ones I’ve bought need to be fucked with every time I go to print. The word I’ve gotten is that these are pretty much ignorable and ready to go even after a long hiatus. And an enclosed build chamber for potentially using ABS again is very interesting to me. I stopped fighting with ABS when PETG came out, but it has it’s own set of shortcomings.
Do it. I was in your shoes about a year ago and finally pulled the trigger on the X1C and haven’t regretted it once. My previous printer was like the ship of Thesius with upgrades and still failed all the time. I’ve got probably 700-800 hours on the X1C and have only had maybe half a dozen prints fail and only one repair needed which was covered under warranty. The only maintenance needed has been greasing the screws, which it kindly informs me to do when needed.
Didn’t get one with my x1c.
I got one with my X1C.
Me too.
I didn’t get any spare parts with my A1 Mini.
You don’t need to replace anything to fix this, though.
deleted by creator
These nozzles are cheap. And it shouldn’t be very difficult fix this one if you have a heat gun. The hard part will be to get at the latch that holds the the nozzle assembly in the extruder. That’s small, fiddly, and delicate part that there is a good chance of breaking.
So while you are ordering that spare heater assembly, ($20US) you might as well get a new nozzle too, ($10US).
You don’t need any new parts to fix this, though, except maybe a new sock. You just heat up your hotend for a while and it’ll pull off. If it’s too thick, stick the hotend in the oven for a bit.
I just had this happen on my X1C for the same reason and was able to get it off after heating up the hotend for a minute and wiggling it loose. Zero residual damage.
