The fusion of light elements up to a certain nucleus size releases energy. However, fusion only occurs at very high temperatures and pressures. The goal is to 1) create the conditions for nuclear fusion (which they did), 2) have the fusion reaction produce energy that sustains those conditions (they did for 48 seconds), and ideally a tiny bit more, 3) gather residual energy that isn’t critical to the reaction itself, which is the part that looks like a steam engine.
The difficult bit is to keep the fuel fusing. At the temperatures and pressures that are needed to get atoms to fuse together the whole lot wants to blow itself apart. Being able to reliability sustain the reaction for any length of time is a big achievement.
Once we can get it to keep going, then yes, we can use the excess heat for power, although it’ll probably involve turbines rather than an old school steam engine type setup.
ELI5 would be huge magnets. If there is something that melts everything humanity ever created and knows of, keep it away from everything. But it is a real problem, instability in the plasma leads to the need for better materials.
Melting actually is not a seriously issue as while the plasma is very hot, it also has very little mass. Sparks are also ludicrously hot but with their little mass contain very little energy so pretty much anything but dry tinder is going to extinguish them before they can do any damage. You want to avoid loss of containment because you will have to clean the reactor vessel and maybe replace a couple of wall tiles but that kind of failure is far from catastrophic.
Though of course with current designs the reactor walls do get hot because that’s how we intend to capture the energy: Pipe water through the walls to cool them, use the hot water to drive a couple of turbines. One of the holy grails to pine for after the current designs actually enter service is to look at ways to drive electrons in a wire directly from the plasma, no detour via heat. The other is aneutronic fusion.
One of the holy grails to pine for after the current designs actually enter service is to look at ways to drive electrons in a wire directly from the plasma, no detour via heat.
That’s actually really interesting, as I never heard of that before.
Yeah you’re absolutely right, damn that’d be one hell of a Holy Grail touchdown moment for Humanity if we could pull that off, the direct transference, no “middle man”.
I mean, in principle we can already do it: Fusion reactions tend to produce lots of electromagnetic radiation, and we can drive wires directly via electromagnetic radiation, the technology is called solar panels. Trouble being solar panels generally aren’t good at absorbing X-rays.
One of the biggest obstacles to magnetic-confinement fusion is the need for materials that can withstand the tough treatment they’ll receive from the fusing plasma. In particular, deuterium-tritium fusion makes an intense flux of high-energy neutrons, which collide with the nuclei of atoms in the metal walls and cladding, causing tiny spots of melting. The metal then recrystallizes but is weakened, with atoms shifted from their initial positions. In the cladding of a typical fusion reactor, each atom might be displaced about 100 times over the reactor’s lifetime.
That’s not the plasma that melts anything but neutron bombardment. The containment and fizzling out issue is the same whether the plasma produces neutrons or just tons of EM radiation which is what I focussed on.
That sturdiness of the cladding things is an important factor when it comes to making cost-effective reactors, that is, the price you sell electricity for needs to cover replacement parts, but is not really that much of an issue when it comes to achieving fusion the materials we have are sufficient for that. Proxima Fusion (the Max Planck spinout) is working on those economical issues for their commercial prototype (early 2030), it remains to be seen whether they go for durable and expensive or cheap but needs to be replaced more often. Which isn’t unusual for power plants in general, none of them run 24/7 they get shut down for maintenance once in a while.
That’s not the plasma that melts anything but neutron bombardment.
I’m aware (I read the article, including the part I quoted you), but regardless of the source of the melting, there is a melting issue of the containment vessel that needs to be engineered away.
Stupid guy here, being ridiculously hot is the whole point right? Isn’t a fusion reactor just an extremely complex steam engine?
https://en.m.wikipedia.org/wiki/Nuclear_fusion
The fusion of light elements up to a certain nucleus size releases energy. However, fusion only occurs at very high temperatures and pressures. The goal is to 1) create the conditions for nuclear fusion (which they did), 2) have the fusion reaction produce energy that sustains those conditions (they did for 48 seconds), and ideally a tiny bit more, 3) gather residual energy that isn’t critical to the reaction itself, which is the part that looks like a steam engine.
The difficult bit is to keep the fuel fusing. At the temperatures and pressures that are needed to get atoms to fuse together the whole lot wants to blow itself apart. Being able to reliability sustain the reaction for any length of time is a big achievement.
Once we can get it to keep going, then yes, we can use the excess heat for power, although it’ll probably involve turbines rather than an old school steam engine type setup.
How are they even containing that heat as this is obviously warm enough to melt everything in existence (as far as I know)?
vacuum for isolation. Magnets, so the plasma stays in the middle and won’t touch the walls. Microwaves to heat it up from the outside.
ELI5 would be huge magnets. If there is something that melts everything humanity ever created and knows of, keep it away from everything. But it is a real problem, instability in the plasma leads to the need for better materials.
It’s moreso keeping it contained at those temperatures, so that it does not melt the container that it’s in, and potentially explode.
There has to be some absolute next-level power backup to keep the containment field from failing.
Melting actually is not a seriously issue as while the plasma is very hot, it also has very little mass. Sparks are also ludicrously hot but with their little mass contain very little energy so pretty much anything but dry tinder is going to extinguish them before they can do any damage. You want to avoid loss of containment because you will have to clean the reactor vessel and maybe replace a couple of wall tiles but that kind of failure is far from catastrophic.
Though of course with current designs the reactor walls do get hot because that’s how we intend to capture the energy: Pipe water through the walls to cool them, use the hot water to drive a couple of turbines. One of the holy grails to pine for after the current designs actually enter service is to look at ways to drive electrons in a wire directly from the plasma, no detour via heat. The other is aneutronic fusion.
That’s actually really interesting, as I never heard of that before.
Yeah you’re absolutely right, damn that’d be one hell of a Holy Grail touchdown moment for Humanity if we could pull that off, the direct transference, no “middle man”.
From the link (for others like me and did not know what the word meant)…
I mean, in principle we can already do it: Fusion reactions tend to produce lots of electromagnetic radiation, and we can drive wires directly via electromagnetic radiation, the technology is called solar panels. Trouble being solar panels generally aren’t good at absorbing X-rays.
Read the below from this article…
That’s not the plasma that melts anything but neutron bombardment. The containment and fizzling out issue is the same whether the plasma produces neutrons or just tons of EM radiation which is what I focussed on.
That sturdiness of the cladding things is an important factor when it comes to making cost-effective reactors, that is, the price you sell electricity for needs to cover replacement parts, but is not really that much of an issue when it comes to achieving fusion the materials we have are sufficient for that. Proxima Fusion (the Max Planck spinout) is working on those economical issues for their commercial prototype (early 2030), it remains to be seen whether they go for durable and expensive or cheap but needs to be replaced more often. Which isn’t unusual for power plants in general, none of them run 24/7 they get shut down for maintenance once in a while.
I’m aware (I read the article, including the part I quoted you), but regardless of the source of the melting, there is a melting issue of the containment vessel that needs to be engineered away.
Yes, and you won’t get me to argue here. I’m too experienced a smart-Alec to contradict another smart-Alec :)
presuming you mean a fusion electricity power plants - maybe. That’s one option.
at those temps, thermoelectric could be interesting.
https://en.wikipedia.org/wiki/Thermoelectric_effect